|
|
Improvement Power Parameter of Small Induction Motors
Halfar, Tomáš ; Ondrůšek, Čestmír (referee) ; Hájek, Vítězslav (advisor)
The master’s thesis Improvement power parameter of small induction motors deals with issues of lowering the losses of small induction motors. The first part introduces with design and principles of operation of induction motors. Also introduces to theoretical problematic of losses, their lowering and measuring. In the practical part there are results of the measuring the losses in the induction motor ATAS Elektromotory Náchod a.s. T22VT512 (71-0512). There are proposed methods of increasing the efficiency of induction motor due to measuring and their verification in the Maxwell software. The last part is dedicated to measuring the losses of prototype motor from ATAS and comparison of results with previous motor.
|
|
|
Reduction of Contact Pairs Friction Losses
Novotný, Marek ; Raffai, Peter (referee) ; Maršálek, Ondřej (advisor)
This bachelor thesis deals with the topic of mechanical efficiency of contact pairs in the crankshaft of the combustion engine. The introductory section focuses on the efficiency of the combustion engine as a whole. In addition, it describes the areas where mechanical losses primarily occur. The following chapters describe mechanism of friction losses, the main factors affecting their amount and the most modern ways to increase mechanical efficiency. In the closing chapter, some basic computing relations, describing the size of mechanical losses are listed. The aim of this thesis is to acquaint the reader with the importance of mechanical efficiency in the area of combustion engines.
|
|
|
Computational modeling of cranktrain mechanical losses
Smetana, Roman ; Píštěk, Václav (referee) ; Novotný, Pavel (advisor)
In the introduction of master’s thesis is introduced the common identification with basics of friction, wear and mechanical losses. Master’s thesis includes description of solving losses by help of the MBS software and analysis of mechanical losses in the crank train. In the last part of work is introduced design for decrease mechanical losses in the crank train. At the close of master’s thesis are reviewed records.
|
|
|
Analysis of steel grade influence on small induction machine efficiency
Plíšek, Oldřich ; Klíma, Jiří (referee) ; Mach, Martin (advisor)
The theoretical part of the bechelors thesis examining the impact of the material of the magnetic circuit on the efficiency of induction motors is devoted to analysis of the induction motor and its losses. It also describes the measuring, including calculations of individual losses. Another theoretical part examines the impact of specific losses on the magnetization characteristics of assessed laminations. The practical part includes laboratory measurements of single phase and three phase motors ATAS Electromotory Náchod brand with multiple types of laminations. Measured values are used to calculate individual losses, which are later mutually compared. Models of measured motors with multiple types of laminations are simulated with the aid of ANSYS Maxwell RMxprt program. Analysis of engines with specific types of laminations are performed with the aid of analytical calculations. Results of calculations are compared with simulated and measured values.
|
|
|
Design of generator with built-in turbine
Palsovics, Norbert ; Ondrůšek, Čestmír (referee) ; Huzlík, Rostislav (advisor)
The task of this thesis is the proposal of a permanent magnet generator with built turbine. This solution has a turbine impeller directly mounted in the rotor synchronous generator with permanent magnets. Integration into the turbine power generator is a major advantage and reduce the dimensions of the whole machine. This system is simple, durable and does not require special service. However, both the rotor and stator of the machine, and special stator winding must be protected against water. The biggest disadvantage of this arrangement is that the water flowing through the gap between the rotor and the stator of the machine causes an increase in mechanical loss. The main objective of this work is to design and calculate the total losses of the machine. The proposal will be validated in a simulation program RMXprt and Ansys Maxwell.
|
|
|
Experimental Determination of Turbocharger Mechanical Losses
Kudláček, Petr ; Doman, Jozef (referee) ; Novotný, Pavel (advisor)
This master’s thesis deals with mechanical losses in turbochargers. The theoretical part provides general information of the methods of support the turbocharger rotor, then focuses on hydrodynamic bearings. The thesis analyzes the occurrence of mechanical losses and the effects that affect them. An important part of this thesis focuses on the determination of mechanical losses and their possibilities. A test stand was compiled for the possibility of experimental measurement of mechanical losses. Several test measurements were performed on this test stand at different operating modes. Simultaneously, the determination of mechanical losses was performed using two other methods. Based on these measurements, it was also possible to perform an evaluation and analyze the occurrence of mechanical losses depending on the set operating conditions. A comparison of individual methods for determining mechanical losses performed in the experimental part was performed. At the end of the thesis, the possibilities of the test stand were defined based on the performed measurements.
|
|
| |
|
|
General Solution of Valvetrain Mechanical Losses
Mynařík, Aleš ; Maršálek, Ondřej (referee) ; Novotný, Pavel (advisor)
This master's thesis deals with the determination of mechanical losses in the valvetrain of the combustion engine. It describes the computational and experimental methods of determining the mechanical losses of valve mechanism. The practical part of the thesis focuses on the programing of structures in Matlab. This application calculates the values of mechanical losses of valvetrain and displays their graphical representation. This program is used for computing the mechanical losses of the selected real engine.
|
|
|
Reduction of Valvetrain Mechanical Losses
Kučera, Pavel ; Píštěk, Václav (referee) ; Novotný, Pavel (advisor)
The topic of this thesis is the mechanical losses in the valvetrain. The purpose is to describe the creation of individual losses and their possible reduction. The main factor of creation of losses is friction. The result of this thesis is to highlight the possible methods to reduce friction and other influences acting on the valvetrain. The main benefit is description various types of surface and design modifications of valvetrains, which are already used or are in development.
|
|
| |
guest ::
